• All polypropylene filter. • High capacity depth filter. • Multi-zone graded-porosity design. • Absolute rating from 0.3 to 50 μm. • Available from 4” to 30” as cartridge or capsule. Electronics Polyolefin range Demineralised water, Solvents, Effluents NT-TE Grade
PTFE Membrane Filters. Biopore Membrane Filter roll, Hydrophilic PTFE This Biopore membrane roll is hydrophilic, with a pore size of 0.4 microns. Milliseal Membrane Seal, PTFE, 18 mm This is a 18 mm Hydrophobic PTFE Membrane Filter with a 0.45 micron pore size. For use in Sterilizing filtration, bioassays, solvent filtration.
PTFE membrane filters have an excellent chemical compatibility (pH 1 to 14), so that they are also used for the filtration of solvents and acids, to which other filter types are not resistant. Moreover they can be used to filter aqueous solutions as well, but because of their hydrophobic characteristics, they must be pre-wetted with ethanol or methanol before the filtration of aqueous media
All Glass Filter Holder/solvent Filtration Apparatus/solvent Filter 1.This product is made of high-quality extra hard glass , no air bubble , sparking and crystal-clear 2.The performance of withstanding voltage and its leakproofness is very good , it can be used for 3.
Hydrophilic PTFE filter The filter element medium for hydrphilic PTFE microporous membrane filter: The hydrophilic stability, high entrapment rate, excellent chemical resistance thermal stability, good strength, impact resistance of the forward & reverse pressure.
High purity PTFE membrane filter media provides superior chemical resistance for a broad range of industrial applications. With retention ratings as fine as 0.01μ (10 nanometers), consistent contaminant removal is achieved in aggressive fluids and organic solvents
Filter both aqueous and organic solvents Optically clear when wet Hydrophilic PTFE membranes are a thin, unsupported, highly porous film that offers maximum chemical and pH resistance to a broad range of aqueous and organic solvents. This membrane exhibits high flow rates with minimal
This 25 mm syringe filter with a Hydrophilic PTFE membrane, for non-sterile filtration, has a 0.45 µm pore size used in low protein binding clarification of aqueous & organic solutions. MillexR syringe filter consists of a membrane sealed in a high density
High-performance filters for HF and BOE recirculation bath processes in ≥10 nm technology nodes. The high-efficiency, high-flow membrane delivers reliable contaminant retention, improving bath quality, and enabling high bath turnover. • Surface-modifiedis non
Cobetter PTFE membrane is a hydrophobic PTFE membrane bonded to a polypropylene support.The extreme chemical compatibility (pH 1-14) makes them very useful for they are also used for the filtration of solvents and acids or other aggressive chemicals, for which
Removal rating: 0.2 µm durability of TETPOR LIQUID filters stems from the use of a single layer, high security PTFE membrane, which has a high dirt holding capacity due to its high void volume. Removal rating: 0.1 µm - 0.45 µm PtSEP Series Pleated Filter Cartridge has the pleated filtration layer composed of PTFE membrane and distribution layer. ...
filters, MultiScreen® multiwell filter plates Polycarbonate Isopore 0.05 µm to 12 µm Philic Low Limited Smooth surface for microscopy Particle analysis, drug permeability & solubility Cut discs, MultiScreen filter plates Nylon Nylon 0.22 µm and 0.45 µm Philic
Membrane Cartridge Filters Available in PES, Nylon, PVDF, PTFE Membrane cartridges filter contaminates on the surface of the media by capturing particles that are greater than the rated pore size. These Absolute rated filters are most often used in sterilizing
