Grade 113 : A creped filter with high loading capacity and the fastest flow rate of any qualitative grade. This is the thickest filter in the range and is extremely strong. Grade 113 is ideal for use with coarse or gelatinous precipitates.
Grade 113 : A creped filter with high loading capacity and the fastest flow rate of any qualitative grade. This is the thickest filter in the range and is extremely strong. Grade 113 is ideal for use with coarse or gelatinous precipitates.
UHF High Flow Pleated Filter Cartridge is a large diameter, coreless single open end pleated cartridge designed to reduce your system investment cost, disposal cost as well as long service life. You can reduce up to 50% of filter system and save up to 60% of change out times compared with conventional cartridge system, and give you a better sealing to ensure a perfect filtration.
Our LifeASSURE™ PFS Series Filter Capsules are constructed to achieve high air flow at a given pressure drop. The PTFE membrane is pleated with polypropylene nonwoven flow-enhancing layers during construction to achieve optimal flow rate performance at low differential pressures. Engineered for Quality and Reliability.
Simsii brings the most versatile range of PTFE membrane filters for air venting, aerosol sampling, and filtration of gases. You can pre-wet hydrophobic filters using alcohol for high flow rates and reasonable pressure differentials. We have a full range of PTFE filters
These highquality membrane filters are made without any adhesives, so there are absolutely no interfering residues. Choose the membrane best for your sterilization method: PTFE or PES Choose the housing material just right for your chemical resistance requirements or sterilization method: PP, PPγ or
TETRATEX ePTFE MEMBRANE MEDIA CHARACTERISTICS Membrane-Air Flow IPA Flow Rate 10-20-0.1 micron 30-40-50-60-70-0-0 10 20 30 Pressure, psi Air Flow, L/min/cm 2 0.2 micron 0.45 micron 0.7 micron 1 micron 1.5 micron100-150-0.1 micron 200-0
High precision depth filter SLF Final filter SHD High Flow Final Filter MGB Developer High flow PTFE membrane CTZ Q-Flow High flow PTFE membrane CTJ High flow rate PP made depth pleat SFP Etching PTFE membrane CTA PP pleats MPX Cleaner CTK
HIGH FLOW TETPOR II gas sterilization fi lters have been developed to benefi t from technological advances within the manufacture of PTFE membranes. This new generation of fi lter sets the standard with an unrivalled combination of effi ciency, fl ow rate and
Flow rates typically 2-3 times that of membrane filters make HIGH FLOW BIO-X the filter that can dramatically reduce cartridge usage and installation size within the fermentation, food and beverage industries. The specially developed PTFE impregnation process
The Chemflow®-XF filter cartridge uses a superior asymmetric PTFE membrane which provides unmatched flow rates and on-stream life. It is constructed with HDPE supports providing an economical alternative to all-fluoropolymer filter cartridges while still maintaining a high
Operating conditions can affect both permeate flux and solute rejection. Among these parameters, permeate flux is very sensitive to the feed temperature. Permeate flux increases as the feed temperature increases. This is mainly due to the decrease of feed viscosity with an increase in the feed temperature.
Filter Media Water wettable Polytetrafluoroethylene (wwPTFE) Pore Size 0.2 μm and 0.45 μm Diameter 25-90 mm Typical Thickness 0.2 μm and 0.45 μm: 280 μm (11 mils) Typical Water Flow Rate mL/min/cm2 at 0.294 bar (29.4 kPa, 4.3 psi) 0.2 μm: 10.9 0.45
Cellulose acetate filter has the characteristics of high flow rate, strong thermal stability, low adsorption, suitable for positive pressure filtration, hydrophilic good performance, uniform pore structure and high flow rate, suitable for pH 3.5 – 8 aqueous solutions or
The PTFE membrane has hydrophobic properties and can filter out water in air and gas. As an absolute retentive membrane, hydrophobic PTFE membrane filters have excellent corrosion resistance and high flow rate, which are equivalent to Millipore membranes. Thin, highly porous, our PTFE disc has OEM service and their sizes could be customized.