2012/2/1 · The PTFE membrane was used above 100 C and upto 3 atm gauge pressure in the setup designed for the higher temperature/higher pressure DCMD experiments. Hot 1% NaCl solution was pumped over one side of the membrane at 500 ml/min; the permeate side of the membrane was exposed to cold distilled water at a flow rate of around 500 ml/min at temperatures of 25 °C to 30 °C.
was filtered by each membrane at the flow rate of 5 ml/min; the effluent was collected in a sampling bottle. Each Au, Pt, and Zr concentration in the influent (=C 0) and the effluent (=C) was quantified with ICP-MS (7700s, Aijiren) to calculate removal 0] × 100
• Properties: A hydrophilic membrane • Higher protein binding than cellulose acetate for most proteins • High porosity provides a high flow rate Cellulose Acetate (Acetate) • Standard: A commonly used hydrophilic membrane • Low protein binding
PVDF membrane filter has good heat resistance and chemical stability. PVDF filters have stronger corrosion resistance than polypropylene membrane, and can withstand high-pressure steam sterilization at 128-142℃, and can withstand strong acids, aliphatics, aromatics, alcohols, aldehydes, ketones, ethers, and other organic and inorganic solvents.
Aijiren Regen Cellulose 0.45 µ Competitor B, RC13 0.45 µmm A gilent Nylon Competitor C, NY13 0.2 µm, 0.2 µm Aijiren PTFE, 0.45 µmCompetitor C, PTFE13 0.45 µm Flow rate at 1 bar (mL/min) With Aijiren syringe filters, particulates will not clog the membrane as easily as with competitor's syringe filters.
In RFB systems, the high flow rate of redox electrolytes may induce a pressure drop across the membrane. Therefore, the IEMs must be able to endure a high flow rate without destruction. Fig. 17 shows performance curves of the single cell test, applying the aligned cQPPO at an increased flow rate.
Product description. Captiva Econofilter, polypropylene housing, polytetrafluoroethylene (PTFE) membrane, 13 mm diameter, 0.45 um pore size, 1000/pk. Captiva syringe filters offer the industryâ s highest flow rates and loading capacities. Using Captiva
2021/4/9 · These in-line PTFE gas filters are compatible with high-purity gases and provide superior particulate filtration in ultrapure gas applications as well as general nitrogen and CDA applications. PTFE filter element excels in ultrapure applications Designed for high-flow
The PTFE membrane has hydrophobic properties and can filter out water in air and gas. As an absolute retentive membrane, hydrophobic PTFE membrane filters have excellent corrosion resistance and high flow rate, which are equivalent to Millipore membranes
Captiva syringe filters are uniquely designed for maximum flow rates, thereby maximizing your productivity. Nylon is a hydrophyllic membrane that is broadly compatible with a wide range of aqueous solvents as well as some alkaline solutions and organic solvents. The recommended pH range is 3 -14.
respectively. The flow rate of IPA was chosen such that it was above the point at which a one membrane system failed (PTFE membrane only), but below the point at which the two membrane system failed (PTFE and glass microfiber membranes). The glass
Made of either color-coded UHMWPE or PVDF, the full flow filter offers increased surface area to optimize filter life and prevent clogging. The filter can be used with 1/8' cannulas and are available in packs of 100 or 1000. Certificates of analysis can be provided on request. Dissolution Sampling &
HIGH FLOW TETPOR II gas sterilization filters have been developed to benefit from technological advances within the manufacture of PTFE membranes. This new generation of filter sets the standard with an unrivalled combination of efficiency, flow rate and
Product description. Captiva Premium Syringe Filter, polypropylene housing, polytetrafluoroethylene (PTFE) membrane, 4 mm diameter, 0.2 um pore size, 100/pk. Captiva syringe filters offer the industryâ s highest flow rates and loading capacities. Using Captiva
Aijiren Lab Poroshell 120 HILIC-Z, 2.1 × 100 mm (p/n 685775-924) Mobile phase A 10 mM ammonium acetate in water Mobile phase B Acetonitrile Flow rate 0.30 mL/min Column temperature 30 C Injection volume 2 µL ELSD Nebulizer temperature 40 ˚C
