Discounting ptfe 0.2 micron filter for solvents

Minisart® SRP15 Syringe Filter 17573----------K, 0.2 µm hydrophobic PTFE Minisart ® SRP with chemically inert hydrophobic PTFE is suitable for venting as well as harsh solvents with a pH of 1 - 14. Type 17573 with a pore size of 0.2 µm can be used for sample preparation and sterile filtration. It has a male luer slip outlet.

Pall AcroPrep Advance Filter Plates for Solvent Filtration - 1 mL, 0.2 µm PTFE membrane (5/pkg) “Pall Laboratory products are designed for laboratory applications only. This product is not approved for use in medical, clinical, surgical or other patient applications.

PTFE Membrane Disc Filters - 2 µm, 47 mm (50/pkg) Product ID. R2PJ047. Material. PTFE with PMP (polymethyl- pentene) support ring. Air flow rate (0.7 bar (70 kPa,10 psi) 53 L/min/cm². Diameter. 47 mm.

Capsules and in-line filters are designed for filtering certain gases or liquids. Choose from disposable or reusable filters for general or specialty uses. When selecting a filter consider the filter media, chemical compatibility, airflow rates, water flow rates, if you need sterile filters, filtration area, filter dimensions, and pore size

Strongly acidic or alkaline solvents might not immediately damage a membrane but can have an effect over time. As such, only highly inert membranes such as PTFE are suitable for high and low pH samples. Depth filtration. In terms of particle retention, filters fall into two categories: surface filters and depth filters.

biological fluids and gases is usually done with 0.2 or 0.22 µm pore filter membranes. Clarification and prefiltration of solutions and solvents is best accomplished with 0.45 µm or larger filter membranes. Prefiltration to improve filter performance can also be accomplished by the use of glass fiber prefilters that can be purchased separately.

, 0.2 µm Aijiren PTFE, 0.45 µmCompetitor C, PTFE13 0.45 µm Flow rate at 1 bar (mL/min) With Aijiren syringe filters, particulates will not clog the membrane as easily as with competitor's syringe filters.

3) KAREI-PTFE-01HL-250-S2C-EX-VR-RPG (PTFE, 0.1 um, Hydrophilic PTFE for liquid application, 250mm, SOE, 222 Viton O-Ring with extended adaptor and stainless steel reinforcement ring, Closed end, Reinforced P.P. with glass parts material)

Pore Size (Metric) 0.2 μm: For Use With (Application) To filter particulates that could damage expensive pumps and detectors, to remove dissolved oxygen in the solvent that could cause detector drift and instability

50mm diameter for gases or 0.2 – 5 L fluid volume, Stepped hose barb inlet and outlet 0.2 PTFE Polypropylene DS0222-0020* 10 0.45 PTFE Polypropylene DS0222-0045* 10

retention ratings of 0.05 μm, 0.1 μm, 0.2 μm, 0.4 μm, 1.0 μm and 5.0 μm, the Ultradyne ® filter is designed for the utmost security in aggressive solvents, highly corrosive chemicals and gases.

The filters are clean and safe as they are almost free of leachables and analytics and withstands even harsh solvents and chemicals. ... 15 mm PTFE PP 0.2 μm ...

Our filters are used for applications requiring 0.2 micron sterilization of air, gas, solvents and chemicals in life science industries. Validated PTFE Membrane Our LifeASSURE™ PFS series PTFE Filters use a hydrophobic polytetrafluoroethylene (PTFE) membrane, which helps minimize pore blockage from moisture in vent applications.

Sartofluor® GA MidiCaps 0.2 μm rated are self contained, ready to use, sterile filter units for sterilizing grade filtration in the pharma/biotech industry. Their unique hydrophobic PTFE membrane is ideally suited for particle removal and sterilizing grade filtration of gases and for filtration of highly aggressive liquids like solvents

Aug 04, 2008 · Filter Media/Support Unsupported PTFE PTFE on a polypropylene support Typical Thickness 140 µm (5.5 mi ls) 0.2 µm: 139 µm (5.5 mils) 0.45 and 1 µm: 135 µm (5.3 mils)